各位看官大家好 今天要跟各位介绍的是
thermalright T-Rad²
唉....又是利民 看不腻啊
这次PO的是新品上市 热呼呼的喔
好了不多说看图吧
外包装 恩 一惯利民朴素的包装
MIC 品质一定OK 吗?? 看下去吧
![](http://xs231.xs.to/xs231/08384/002136.jpg)
T-Rad²能登上新的显卡散热王者吗
![](http://xs231.xs.to/xs231/08384/003322.jpg)
开箱啦
![](http://xs231.xs.to/xs231/08384/004646.jpg)
说明书
![](http://xs231.xs.to/xs231/08384/005348.jpg)
贴纸
![](http://xs231.xs.to/xs231/08384/006722.jpg)
看到散热器了
![](http://xs231.xs.to/xs231/08384/007706.jpg)
拿出来了
![](http://xs231.xs.to/xs231/08384/008750.jpg)
登场啦 各位慢慢看图 不多说啦
![](http://xs131.xs.to/xs131/08384/009833.jpg)
![](http://xs131.xs.to/xs131/08384/010564.jpg)
![](http://xs231.xs.to/xs231/08384/011646.jpg)
![](http://xs231.xs.to/xs231/08384/012968.jpg)
![](http://xs231.xs.to/xs231/08384/013790.jpg)
![](http://xs131.xs.to/xs131/08384/014172.jpg)
![](http://xs231.xs.to/xs231/08384/015562.jpg)
![](http://xs231.xs.to/xs231/08384/016744.jpg)
![](http://xs231.xs.to/xs231/08384/017553.jpg)
配件
![](http://xs231.xs.to/xs231/08384/018730.jpg)
拆开风扇固定架 看得更深入更仔细
![](http://xs231.xs.to/xs231/08384/019918.jpg)
![](http://xs231.xs.to/xs231/08384/020341.jpg)
![](http://xs231.xs.to/xs231/08384/021236.jpg)
![](http://xs131.xs.to/xs131/08384/022567.jpg)
要装风扇啦 要装的是AC 9 PWM
![](http://xs131.xs.to/xs131/08384/023415.jpg)
对没看错就是他
连小4pin都改好了 呜呜~~~保固
![](http://xs131.xs.to/xs131/08384/024665.jpg)
装不上怎么办 没关系 把螺帽熔进去吧
![](http://xs231.xs.to/xs231/08384/025838.jpg)
![](http://xs231.xs.to/xs231/08384/026298.jpg)
完工
![](http://xs231.xs.to/xs231/08384/027276.jpg)
厚度就这样
![](http://xs231.xs.to/xs231/08384/028969.jpg)
前面说MIT就一定好吗
不一定 看看下图
![](http://xs231.xs.to/xs231/08384/029496.jpg)
![](http://xs231.xs.to/xs231/08384/030799.jpg)
![](http://xs231.xs.to/xs231/08384/031251.jpg)
就当作没看到好了
测试方法
关机壳 风扇配置如下图
![](http://xs231.xs.to/xs231/08385/032907.jpg)
测试软体为FurMark
使用FurMark_v1.4.0\shttp://bbs.mychat.to/post.php?fid=457tart-Xtreme-Burning.bat批次档
可以烧出比Stability Test更高的温度
开始测吧
原厂温度如下
![](http://xs231.xs.to/xs231/08385/1580.jpg)
![](http://xs231.xs.to/xs231/08385/2259.jpg)
可以看到原厂风扇只要降低转速温度就会往上飙
而且四跟热管好像不够力的样子
快快来装吧
先拆掉原厂散热 清一下灰尘跟散热膏
![](http://xs231.xs.to/xs231/08385/033719.jpg)
贴上散热片 因为热导管的位置不同 所以薄的散热片贴的位置也不同
![](http://xs231.xs.to/xs231/08385/034389.jpg)
电源IC端
![](http://xs231.xs.to/xs231/08385/035848.jpg)
不得不抱怨一下 利民附的散热片黏度不够喔
害我贴个老半天 重新用过别的贴布就OK
散热器锁上螺丝 放上软的垫圈
![](http://xs231.xs.to/xs231/08385/036338.jpg)
撕掉保护的膜 放上散热器 在放上保护的垫片
![](http://xs231.xs.to/xs231/08385/037315.jpg)
锁上螺丝
![](http://xs231.xs.to/xs231/08385/038634.jpg)
请忽略上面的弹簧 试验后发现不可行
开始测试吧 结果如下
![](http://xs231.xs.to/xs231/08385/3831.jpg)
![](http://xs231.xs.to/xs231/08385/4807.jpg)
六根热导管果然就是不一样
即使转速降到30%才原厂散热的70%而已
温度差了18度之多
记得我之前买的HR-11吗?? 装上去吧
![](http://xs231.xs.to/xs231/08385/039807.jpg)
上机去
![](http://xs231.xs.to/xs231/08385/040432.jpg)
结果如下
![](http://xs231.xs.to/xs231/08385/5436.jpg)
![](http://xs131.xs.to/xs131/08385/6822.jpg)
有了系统风扇的帮忙 温度又下降了5度之多
最后来个总整理吧
![](http://xs131.xs.to/xs131/08385/7197.jpg)
![](http://xs131.xs.to/xs131/08385/9583.jpg)
![](http://xs131.xs.to/xs131/08385/8804.jpg)
![](http://xs231.xs.to/xs231/08385/10735.jpg)
优点:
1.很方便的安装方式
2.很薄
3.效能很不错
缺点:
1.很卡 卡很多东西 卡南桥 卡SATA 卡电源线
(解决方法:
凹南桥散热器
买下图"短头"的SATA线
![](http://xs231.xs.to/xs231/08385/041718.jpg)
把电源线卡榫剪断
![](http://xs231.xs.to/xs231/08385/042483.jpg)
)
2.附的散热片黏度不足
3.散热起本体有黄黄的东西附着没有洗干净 散热片也有凹到的痕迹
4.MIC.....